Ford axle identification.

Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-In most cases, the short axle goes in the driver's/left side. In the above video, you'll see us installing the axle, then measuring out to the end of the bearing. You can also stick a tape measure into the axle tube and measure to the stop in the differential. As we measured, we did not account for the thickness of the backing plate.Look at the tag on your driver door. There is a category for Axle Code. Look at that code then Google it. You likely have 3.55 if you have a 4x4 or FX4 or max towing. Otherwise 3.31 would get my vote. The 10 speed trans defaults to the 3.31 unless other criteria is met as the 3.31 is a perfect match for the 10 speed.Ford Rear Axle Assembly Identification - Page 16: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V012-A: Ford Pass., Mercury 86-91: 2.73: 8.8: NL: 28-V012-B:

Dana Differential Identification. The Bill of Material (BOM) number is used to identify Dana differentials. Traditional BOM's are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits, such as 605561-1. Later-model BOM's may start off with the first three digits of 200 rather than 60 or 61, for example 200561-1.

Check the code on the door jab, loooks to be 410 in front,which is pretty obvious. I have the code book that came with my truck,if u post the code. V131C = F-250/350 PU '87-'96 4.10, 10.25 ring gear, limited slip. 1987 - 1996 F150 & Larger F-Series Trucks - axle identification - i just pulled the axle tags from my truck and after some …Likes: 33. Received 73 Likes on 39 Posts. Visual Confirmation of 10.5" Sterling Rear Axle? According to the rule of thumb (all 250s w/o the HD pkg get the Sterling; truck is a 2019 F250 Powerstroke), I should have a 10.5" Sterling, 35 spline rear axle. Door jamb Axle code is "3H" (3.31, electronic locking)

If we go to the Dana Part Identification Page, we see that this axle is from a Ford F250/350 SRW (Single Rear Wheel - Non-Dually) 4×4. The results can be seen HERE. The number on the top left of this sticker in 610366-8. Using the same method to look up this number, we find that it is a Dana 35 from a Ford Explorer. Axle Tags & Door Stickers:May 1, 2000 ... Actually every 91-94 Explorer has a Dana 35 IFS Reverse Rotation and every 95-01 Has a Hybrid Dana 30/35.Axle Assembly. Ford Parts are the Only parts designed and built to the specific Standards of Ford Motor Company and are the Only parts recommended for use in your Ford or Lincoln vehicle. Right. Narrow axle. 4wd, f250,f350. To 10/01/2014. From 10/01/2014. w/ 4wd, w/o hd Suspension. Exc.Wide Track Front Suspension.Large Truck - Axle Codes for 1990's Louisvilles - Hello all, I am trying to determine the axle ratio on a 1994 LTS9000 that has a door post axle code of 6A. On my older L9000's (1970's and 80's vintage) I have the Ford Shop Manuals that under identification codes decode the 23,000 lb single and tandem axle codes...Find the word "AXLE" under the bar code. 3. Find the two-digit code under "AXLE." Step 2 - Find the Axle Ratio. To locate the axle ratio after you have found the axle code: Visit the RV & Trailer Towing Guides page on the Ford Fleet website. Select the Towing Guide for your vehicle's model year. Note: Rear axle ratios are available for 2008 and ...

The vehicle identification number for Ford cars and trucks is a 17-digit series of numbers and letters that identifies an individual vehicle and certain aspects of the vehicle’s co...

For 2015 models, the maximum towing capacity of a Ford F-350 ranges from 12,100 pounds to 26,500 pounds, depending on the configuration of the vehicle and the trailer. Vehicle opti...

1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks - Axle identification. - Greetings :) I am replacing the ball joints on my '84 F-250 work truck, but for some reason the ID sticker inside the door is missing, and the serial number has been re-issued. The folks at AutoBone need the GAWR for the front axle with...At least the rear end appears to be original. Dave R. I recall reading somewhere that only 428CJ and Boss 302 cars received 31 spline axles. The best way is to pull the axle. While it is possible to identify a factory axle from the outside, the same rules do not apply to aftermarket axles.Ford Rear Axle Assembly Identification - Page 14. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Dec 25, 2023 · The code can be found on the Vehicle Identification Number (VIN) label, which is typically located on the driver’s side door jamb or the front windshield. 2. Decoding the Axle Code. To decode the Ford Axle Code, you need to refer to the manufacturer’s specifications or consult an online decoding tool. The code is made up of several ... Nov 27, 2017 · F-350 rear axle identify. I bought a rear axle with a broken ring gear for a project truck. In working on my F350 driver I needed to replace a rear caliper and found there was a right and left. I thought (scary things happen) and looked at my project rear axle and it does not have a right or left. The right caliper hangs on the rear and the ...

Chrysler 11.5” Rear. Chrysler 11.8” Rear. Dodge Dana 60. Chrysler / Dodge - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. Chrysler has a wide range of front and rear ends! We carry everything from the 7.25" front and rear end parts, to the large 11.8" rear end parts for Ram ...Depending on the model, you can typically find it on the driver’s side door jamb, the glove compartment, or in the owner’s manual. Additionally, there are online resources that provide comprehensive lists of axle codes for various Ford models to help you identify the specific code for your vehicle. differential ford axle code chart.The Ford 8.8 differential ID tag attached to the differential will tell you the gear ratio, rear end style, and whether it has limited-slip. Also on the tag is an ID number, which, until 1985, included four to five letters and no numbers. Almost all 8.8s - and all post-'86 Ford rear ends - have letters and numbers.The 1957-1959 Ford styling revolution brought such cars as the Mystere show car and the Skyliner. See pictures and learn all about 1957-1959 Ford styling. Advertisement The 1957 st...The number in the name (Dana 30, Dana 44, etc.) is in reference to this. Dana 30: This axle size is the most common, and you'll only find it on the front of Jeep. They have a ring gear diameter of 7 and 1/8 inches. The Dana 30 gear ratios are either 3.21 or 3.73. The width of the axle shafts is 1.13 inches.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle Identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines.

Contact. You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 15. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 15. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L.Common axle ratio variants in Ford F150. Variants of Ford F150s have been built with varying axle ratios depending on the model year, engine size, or intended use. Commonly, we encounter axle ratios like 3.55, 3.73 or 4.10 in F150 models. This information can be found on the rear end tag or in the vehicle's service manual.

The Following Is a List of Common Dana 61 BOM Numbers - These Axles are NOT Dana 60 Axle: 603925-1. 603946-1. 605022-17. 605039-7. 605064-4.ID a 1974-1975 Ford Dana 60 Closed Knuckle Front Axle IDN-133 $0.00 1974-1975 Dana 60 Front Axles in Ford Trucks had a Ford Axle Code Tag with the Ford Production Part Number and Dana Bill of Material Number (BOM) stamped on a metal Build Tag (red arrow) attached to the differential by two of the differential cover bolts...ID a 1974-1975 Ford Dana 60 Closed Knuckle Front Axle IDN-133 $0.00 1974-1975 Dana 60 Front Axles in Ford Trucks had a Ford Axle Code Tag with the Ford Production Part Number and Dana Bill of Material Number (BOM) stamped on a metal Build Tag (red arrow) attached to the differential by two of the differential cover bolts...That said, they're not failure prone until you lift the trucks and run big tires. For normal trucks, they still last forever and a day. Awesome thanks. 1987 - 1996 F150 & Larger F-Series Trucks - Rear F350 Axle Tag Identification (help) - Sorry in advance that I dont have a better photo, but I stumbled across a 1990 F350 SRW 5.8L 5-speed today ...The axle that came in that truck from the factory..... Dana 80 disc brakes 5.15 gears 10 on 7.25 bolt pattern 8 bolt axle stub Now the oddity... The 5 bolt axle stub really throws me off And the drum brakes, these trucks were ALL disc brakes it also looks like someone has put a set of 19.5 wheels/tires on as wellHousing Identification. 57 - no dimples, flat center band up the center of the rear cover, bottom drain plug. 58-59 - two dimples on back of housing, flat center band, some had drain holes. 60-67 - two dimples, flat center band, oil level hole in back cover. 63-77 Lincoln, LTD, Thunderbirds had 9.375 inch centers, housings were cut away at the ...1932-1934 the wishbones are bolted to the bottom of the axle housings about 8" from the ends. the tabs for the wishbones are welded on, but will not go all the way around the housing, just the bottom. the spring hangers are forged on to the axle tubes. on the 1932, the part where the torque tube bolts to the diff is round (most) it is more of a ...

No idea, the above diagram I posted came straight out of the Ford shop manual that dealer tech's use. 2009 - 2014 Ford F150 - Help Me ID This Rear Axle (Code S930P) - I'm looking to buy a rear axle assembly to mock up some things for a project I'm starting and I'm wondering if anyone can help me identify which rear axle is in this picture, the ...

Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks. Rear Axle Identification. 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks Discuss the Early Eighties Bullnose Ford Truck.

The 1963 Ford body plate data decoder enables you to discover the vehicle's build information including paint color, body style and trim. FORD Body Plate IdentificationE350 Axle Identification. I've got a 1998 E350 extended club wagon SRW, Limited Slip, 3.55. The rear end is making noise at highway speed. Not really a howl, more like a wining sound...like a … Axle codes for Ford Explorer, Ranger and Bronco II. Axle identification Ford Explorer, Bronco II, Ranger. The right ratio. If the tag reads S806D the axle was made for a F 150 Pickup 87-95, E150 Van 87-95, Bronco 87-95. It is a 8.8 In. with a gear ratio of 3.08. It is also a unlocking diff. Hope this clears anything up. Ralph [email protected]. Reply Like. # 8. 09-18-2010, 03:03 PM.When ordering Dana/Spicer Differential Parts provide bill of material number. This number is stamped on your right hand side axle tube. It's a number like 603XX-X, 604XX-X or 605XX-X. With this number you can tell exactly what components the factory used in the assembly of your differential. What is my Ford rear end ratio, do I have ...If we go to the Dana Part Identification Page, we see that this axle is from a Ford F250/350 SRW (Single Rear Wheel - Non-Dually) 4×4. The results can be seen HERE. The number on the top left of this sticker in 610366-8. Using the same method to look up this number, we find that it is a Dana 35 from a Ford Explorer. Axle Tags & Door Stickers: Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L. Mean Max. 14314 posts · Joined 2007. #8 · May 9, 2009. You'll want one from an Explorer. '95-'01 will get you rear disc brakes, earlier models will have drums. Look on the driver's door of the donor Explorer for the axle code on the VIN sticker. Explorer 8.8 Axle codes. 43 Open 3200 3.08. 41 Open 3200 3.27.Ford only used 3800 pound rated Dana 60 closed knuckle front axles in 1974 and 1975 F-250 Crew Cab 4x4 trucks. Externally, the axle looks very similar to the Dana 44HD axle that was an option on F-250 regular cab models. Ford built a good number of 1974-1975 Crew Cab F-250 4x4s, but most were shipped to Alaska for use during the construction of ...2000 F250 Front Axle ID. Hello. I recently acquired a 2000 F250 and was trying to ID the front axle. There is no code on the door sticker and after running the VIN at work, there is no code there either. The only thing I found was in the list of build codes, theres an MFAL reading "Heavy Duty Frt suspension" and also, "ambulance package".

Clutch, Transmission, Differential, Axle & Transfer Case. 1. 09-08-2004 09:00 PM. /. 2004 - 2008 F150 - Axle identification - On my 04 lariat 4x4 the axle code is 26, which from my research says 3.73 non limited slip. Which a 4x4 with non LS is a sad thing. But when I spin the tires they both spin.Depending on the model, you can typically find it on the driver’s side door jamb, the glove compartment, or in the owner’s manual. Additionally, there are online resources that provide comprehensive lists of axle codes for various Ford models to help you identify the specific code for your vehicle. differential ford axle code chart.Assemble pinion mate cross shaft, make sure lock pin hole of the shaft is in verticle position and lined up with the lock pin hole of the case. Step (15) Assemble new roll pin. Peen metal of case over pin to lock in place. Step (16) Secure end yoke or flange with holding wrench, and remove pinion nut and washer.Step 3. Locate the identification tags on the rear-end housing unit. According to the Dana/Spicer Corporations' "Roadranger" Illustrated Parts List, there are two identification tags, one located on the driver's side differential carrier and one on the passenger side of the axle housing. Both tags contain similar information, however, the axle ...Instagram:https://instagram. bras for crossdressingis alex biston marriedrubyscale outpostspanish article crossword See All 52 Photos. Detailing a rear axle is a major part of a Mustang concours restoration, right up there with the engine and the front suspension in complexity. There are so many parts, colors ... ccbi arrest recordscrowder leaked video When it comes to maintaining and repairing your vehicle, using high-quality auto parts is essential. One name that stands out in the industry is Detroit Axle. With their reputation...Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by: food city 706 Jul 12, 2015 ... Re: Axle identification ... From memory it does, I'm nearly sure it had the removable cover plate. There are two with removable plates. A strong ...The axle shafts are TINY. A 7.5" Ranger axle has stronger shafts. Even with 35 spline chromoly shafts, the axles will break first. If you can't find any more numbers, look at the cover. On a 60, the bottom of the centersection closely follows the cover. A 70 uses the same cover.Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.